XLink Kai is a free peer-to-peer LAN tunneling service that has been running since 2003. It makes your PS2 treat far-away players as if they were on your local network, so games with a system-link (LAN) mode can be played online. XLink officially supports 56 PS2 LAN games - check the supported games list for yours.
Use your own legally obtained copy. We recommend that you use your own legally obtained copy of the game. ROM does not condone illegally downloading ROMs.
What you need
- A PlayStation 2. Fat models need the official Network Adaptor; slim models have networking built in.
- A PS2 memory card - the network profile is saved to it.
- One of the 56 supported LAN games.
- A way to open the PS2 network settings utility: a game with the utility built in, or a modified console running uLaunchELF.
- A PC, Mac or Raspberry Pi running the XLink Kai client, plus Ethernet cable(s). The computer running Kai cannot be fully wireless on the link toward the PS2 - if it has no Ethernet port, use a USB Ethernet adapter.
Account and client
- Sign up on the XLink Kai home page and verify your email address. Read the Acceptable Use Policy.
- Download and install the client for your OS - official install guides cover Windows XP to 11, macOS, ChromeOS and Raspberry Pi. On Windows, Kai needs the WinPcap or Npcap driver; if Kai will not start, that driver is the usual cause. There is no official desktop Linux guide yet.
Connect the console
- Best: wire both the PS2 and the computer to your router with Ethernet - the lowest latency and most stable link.
- Semi-wireless: connect the computer directly to the PS2 with an Ethernet cable; the computer can still reach the internet over WiFi. Do not bridge adapters and do not enable Internet Connection Sharing - only the computer needs internet.
Network profile on the PS2
Load the network settings utility from a game that has it (in Star Wars Battlefront: Multiplayer > LAN > OK, then press Square). Menu names vary per game.
- PS2 connected directly to the computer (no bridging, no ICS): an Automatic (DHCP) profile is fine - just start Kai and log in before powering on the PS2.
- PS2 on your home network or WiFi (recommended there): set a Manual profile. XLink derives the address from your console's MAC address:
- Create a temporary Automatic profile first; before saving, the screen shows the MAC address. Write down its last 4 digits, then cancel with O.
- Open the XLink IP calculator, choose Sony Playstation 2, enter the 4 digits and calculate.
- Create a new profile, set IP Address to Manual and enter the IP, netmask and default router from the calculator.
- Set DNS to Manual and enter 10.253.0.1 as the Primary DNS.
- Name and save the profile. Skip the connection test - on real hardware it always fails, and that is normal.
Play
- Start XLink Kai on the computer and log in.
- In Kai, open Game Arenas and navigate to your game's arena.
- On the PS2, load the game, choose Multiplayer > LAN, select your network profile, then Join or Create.
- In Kai's Metrics tab your PS2 should show as Configured OK. Join a match and play.
If it does not work
- The LAN option is greyed out: reseat the Ethernet cable on both ends or try another cable.
- Other players show "No connection": a closed port on your side or theirs. UPnP usually handles this, but if it happens often, forward the UDP port shown in Kai's configuration menu to the computer running Kai, and keep your router's DMZ disabled. With two routers (double NAT), set one to bridge mode.
- You can ping players but see no matches: make sure everyone has the same game updates and region; ask someone in the arena to search while you watch Metrics - inbound broadcast traffic should tick up from 0. If the adapter shows no traffic, select it manually in Kai's configuration menu.
- The network adapter is missing from Kai's configuration menu on Windows: open an admin command prompt and run
net stop npfthennet start npf. - More help: the official Team XLink Discord runs game-specific channels, and fan Discords host regular game nights.