ROMUnite.

Type a game, a player's name, a console or a way to play online.

Sign in

Connect an original Xbox to XLink Kai

XLink Kai · Real Xbox (real hardware) · updated Nov 16, 2026 by Andrew4Lyf

For Real Xbox Plays with xemu on XLink Kai Not checked with Dolphin · Real GameCube · Ryubing (Ryujinx) · Real Nintendo Switch · PCSX2 · Real PS2 · RPCS3 · Real PS3 · Real PSP · Vita3K · Real PS Vita · Xenia Canary · Real Xbox 360

Read in: EnglishDeutschEspañolFrançais日本語PolskiPortuguêsРусский

XLink Kai is a free peer-to-peer LAN tunneling service that has been running since 2003 - the original Xbox was one of its launch consoles. It puts your console and other players on the same virtual network, so games with a system-link mode can be played online. XLink officially supports 139 original-Xbox system-link games, all verified - check the supported games list or look for "System Link" on the back of the game case. Many original Xbox games also work under backwards compatibility on Xbox 360 and Xbox One, where the 360's ping limit does not apply to them.

Use your own legally obtained copy. We recommend that you use your own legally obtained copy of the game. ROM does not condone illegally downloading ROMs.

What you need

  • An Xbox console (retail or modded - XLink supports both).
  • One of the 139 supported system-link games.
  • A PC, Mac or Raspberry Pi running the XLink Kai client, plus Ethernet cable(s). The computer running Kai cannot be fully wireless on the link toward the console - if it has no Ethernet port, use a USB Ethernet adapter.

Account and client

  1. Sign up on the XLink Kai home page and verify your email address. Read the Acceptable Use Policy.
  2. Download and install the client for your OS - official install guides cover Windows XP to 11, macOS, Raspberry Pi and ChromeOS; their Quick Start notes a desktop Linux install guide is still pending. On Windows, Kai needs the WinPcap or Npcap driver; if Kai will not start, that driver is the usual cause.

Connect the console

  • Best: wire both the Xbox and the computer to your router with Ethernet - the lowest latency and most stable link.
  • Semi-wireless: connect the computer directly to the Xbox with an Ethernet cable; the computer can still reach the internet over WiFi. Do not bridge adapters and do not enable Internet Connection Sharing - only the computer needs internet.
  • Power on the Xbox and check the link light on its Ethernet port. If the console is connected directly to the computer and the light stays off with a known-good cable, the computer's network interface may be too old for Auto MDI-X - use a crossover cable.

Play

No network profile setup is needed on the Xbox - system link just works once the cable is connected.

  1. Start XLink Kai on the computer and log in.
  2. In Kai, open Game Arenas and navigate to your game's arena (the official guide uses Halo 2).
  3. On the Xbox, load the game (from disc or HDD) and choose System Link from its menu - in Halo 2: press START, pick your profile, choose "Don't sign in", then SYSTEM LINK. If the cable is not connected, the game will tell you.
  4. Join or create a match. If you see no matches, check Kai's Metrics tab: your Xbox should be listed. If it is missing, recheck the cabling, run Kai with administrator rights on Windows, and allow it in the firewall.

If it does not work

  • System Link is greyed out in game: check the link light and try another Ethernet cable.
  • "Wrong IP Detected" under your console in Metrics: safe to ignore unless you are playing homebrew games.
  • Other players show "No connection": a closed port on your side or theirs. UPnP usually handles this; if it happens often, forward the UDP port shown in Kai's configuration menu to the computer running Kai, keep your router's DMZ disabled, and with two routers (double NAT) set one to bridge mode.
  • You can ping players but see no matches: ask someone in the arena to search while you watch Metrics - inbound broadcast traffic should tick up from 0. If the adapter shows no traffic, select it manually in Kai's configuration menu.
  • The network adapter is missing from Kai's configuration menu on Windows: open an admin command prompt and run net stop npf then net start npf.
  • More help: the official Team XLink Discord runs game-specific channels, and fan Discords host regular game nights.

Play it with people

Find people to play Xbox with

1 member here plays XBOX. Set up once, then the site tells you when they're on.

Nothing open right now. Open a lobby and the members who play it hear about it.